Radiator installation in Central London
New radiators, like-for-like replacements, radiators moved during a refurbishment, and heated towel rails. Sized to the room, fitted neatly and balanced, with a free quote first.
Radiator jobs we do
From swapping one radiator to re-planning a whole flat.
Replacement radiators
Like-for-like or a better size
New radiators
Extra heat in a cold room
Moving a radiator
Pipework re-routed for a new layout
Heated towel rails
Plumbed, electric or dual fuel
Column and designer radiators
For period flats and refurbishments
Thermostatic radiator valves
Room-by-room temperature control
Cold spots and balancing
Radiators that heat unevenly
Leaking radiator valves
Drips at the valve or the joint
More →What you get
- Each radiator sized to the room's heat loss
- Pipework run neatly, in walls or floors where practical
- System drained, refilled and checked for leaks
- A free quote, agreed before work starts
- Radiators balanced so every room heats evenly
- Floors and furniture protected, everything cleaned up
Send us a photo — we’ll tell you what it is and what it takes to fix it.
Experienced trades, not a middleman
A radiator that is too small for the room never gets it warm, and one in the wrong place wastes the wall. We size radiators properly and fit them so they look as if they were always there.
Choosing and fitting the right radiator
Most radiator problems come down to size, position or the state of the system. A radiator should be sized to the heat the room loses, which depends on its size, its windows, its outside walls and the floor above and below. A bay-fronted reception room in a mansion block needs far more heat than a bedroom of the same floor area at the back.
Types of radiator
- Panel radiators, single or double, are the standard choice and give the most heat for the money.
- Column radiators suit period flats and houses and come in a range of heights and finishes.
- Vertical and designer radiators free up wall space where a long radiator will not fit.
- Heated towel rails can run on the heating, on electricity, or both, so they still work in summer.
Replacing a radiator
Replacing a radiator like for like is often quick, but older radiators rarely match modern sizes, so the pipework usually needs adapting. We drain the system, fit the new radiator and valves, refill, bleed and check every joint. If the old radiators are full of sludge, we will tell you, because a new radiator on a dirty system will soon have the same problem.
Moving radiators during a refurbishment
Moving a radiator means re-routing the flow and return pipes. In a flat with solid floors or a concrete slab, that needs planning, and it is far easier to do while floors are up during a refurbishment. We plan radiator positions with the rest of the work so pipes are hidden.
Thermostatic valves and balancing
Thermostatic radiator valves let you set each room's temperature and stop rooms overheating. When some radiators are hot and others barely warm, the system usually needs balancing: adjusting the valves so heat reaches every radiator evenly. We do this after every installation.
Flats with communal heating
Some mansion blocks have communal heating, where the pipes and the plant belong to the building. Changing radiators on a communal system may need the managing agent's agreement and the system to be drained at block level. We check before quoting.
Sorted in 3 easy steps
This is exactly what happens after you get in touch.
Tell us what’s wrong
Fill in the form, call us or send a photo on WhatsApp.
Get a free quote
We look at the job and tell you what it will cost — before anything starts.
We fix it
Pick a time that suits you. The quote is agreed before work starts.
Areas we cover
Mayfair
W1K · W1JView area →Marylebone
W1U · W1GView area →Fitzrovia
W1T · W1WView area →Paddington
W2View area →Bayswater
W2View area →Little Venice
W9View area →Maida Vale
W9View area →St John’s Wood
NW8View area →We also cover Soho, Westminster, Kensington and Notting Hill — see all areas.
Your questions, answered
Can you replace a radiator without draining the whole system?
Sometimes. On some systems we can isolate the radiator and drain only what is needed. Moving a radiator, or replacing several, usually means draining the system down.
How do I know what size radiator I need?
It depends on the room's heat loss: its size, windows, outside walls and the rooms around it. We work this out when we survey, so the new radiator actually heats the room.
Do new radiators need a Gas Safe engineer?
Radiators are water-side plumbing, so fitting them is not gas work. If the boiler needs adjusting or replacing as part of the job, that part is done by a Gas Safe registered engineer.
Why is my radiator cold at the bottom?
That is usually sludge collecting at the bottom of the radiator. Cold at the top usually means trapped air, which bleeding fixes. We can flush a sludged system or replace badly affected radiators.
Can you fit radiators in a listed or period building?
Yes. Column radiators suit period interiors. In a listed building, some changes need consent, so check with the council first. Our guide to listed building consent explains more.
Guides for this job
Underfloor heating in a bathroom
Is it worth it in a London flat?
Read →Boiler losing pressure?
Leaks, valves and what to check
Read →Period property refurbishment
Planning work in older buildings
Read →Listed building consent
When you need it
Read →More help: plumbing · boiler installation · refurbishment · emergency plumber
Got something that needs fixing?
Get a free quote today — agreed before any work starts.