Plumbing · Hot water

Water heater repair and replacement in Central London

No hot water, water that never gets properly hot, or a cylinder that drips or trips the power. We find out why, repair what can be repaired and replace what can't, with a free quote first.

Get a free quoteTell us the job — most quotes come back the same day. Free quoteNo obligationCentral London team

Hot water jobs we do

From a failed immersion element to a new cylinder.

Immersion heater replacement

New element or thermostat in your cylinder

Hot water cylinder replacement

Old, leaking or undersized cylinders

Unvented cylinders

Mains-pressure hot water, fitted and serviced

Under-sink water heaters

Instant hot water at one tap

Electric instantaneous heaters

Hot water on demand, no tank

No hot water from the boiler

Combi and system boiler faults

More →

Immersion tripping the power

Element earth faults

More →

Low hot water pressure

Weak flow from the hot taps

More →
Included every time

What you get

  • The fault found before anything is replaced
  • The right size of heater for the flat and the people in it
  • Unvented cylinders fitted by a qualified installer and registered
  • A free quote, agreed before work starts
  • Old cylinder drained, removed and taken away
  • Temperatures set and tested before we leave
Need it sorted quickly?

Same-day and emergency slots across Central London, availability permitting.

Why fixmyproperty.ai

Experienced trades, not a middleman

Most Central London flats get hot water from a combi boiler, an immersion heater in a cylinder, or a small electric heater under the sink. We work on all three, and we tell you honestly whether a repair or a replacement makes more sense.

Repair or replace your water heater?

Water heaters fail in a small number of ways. An immersion heater element burns out or develops an earth fault, a thermostat sticks, a cylinder starts to weep at a joint or along a seam, or a valve on an unvented system stops doing its job. Finding which one it is matters, because the fix ranges from a new element in one visit to a new cylinder.

Signs your water heater needs attention

  • No hot water at all, or only lukewarm water.
  • The immersion switch trips the electrics or the fuse board.
  • Water around the base of the cylinder or a damp cupboard floor.
  • Water dripping from a small pipe under the cylinder, or into a funnel-shaped fitting called a tundish. On an unvented cylinder this means a safety valve is opening, so turn the heating of the water off and call an engineer.
  • Rumbling, banging or hissing as the water heats.

Immersion heaters

Many flats with electric hot water have an immersion heater: a long element inside the cylinder, controlled by a thermostat. When the element fails, it can usually be replaced without changing the cylinder. If the cylinder itself is old, corroded or leaking, replacing the whole unit is usually the better job.

Unvented cylinders

Unvented cylinders run at mains pressure and give strong showers without a tank in the loft. Because they are stored under pressure, the building regulations require them to be fitted by a qualified installer and the installation to be notified. They also need an annual service to check the safety valves.

Under-sink and instantaneous heaters

Where a kitchen or cloakroom is a long way from the main hot water, a small heater under the sink or an instantaneous electric heater can give hot water straight away. They need the right electrical supply, so we check the circuit before recommending one.

What temperature should hot water be?

The Health and Safety Executive advises that stored hot water should be kept at 60°C or above to control legionella bacteria. Water that hot can scald, so where children or older people use the bathroom, a thermostatic mixing valve can deliver it to the taps at a safer temperature.

Gas water heaters and combi boilers

If your hot water comes from a gas boiler, the fault is often in the boiler itself, not the hot water side. Gas work is done by Gas Safe registered engineers. See our boiler installation page and our guide to a boiler not heating water.

Sorted in 3 easy steps

This is exactly what happens after you get in touch.

Get my free quote →
What needs fixing?No hot water from the cylinder photo.jpg ✓
1

Tell us what’s wrong

Fill in the form, call us or send a photo on WhatsApp.

fix. Your quote is readyReplace the immersion element and thermostat. One visit.Accept quote
2

Get a free quote

We look at the job and tell you what it will cost — before anything starts.

Choose a timeWed 2pmThu 10amFri 9am Booked — Thu 10:00
3

We fix it

Pick a time that suits you. The quote is agreed before work starts.

Your questions, answered

Can you replace just the immersion heater?

Usually, yes. If the cylinder is sound, we drain it down, replace the element or thermostat and refill. If the cylinder is corroded or leaking, we will say so and quote for a replacement instead.

How long does a water heater replacement take?

Replacing an immersion element is usually one visit. Replacing a cylinder takes longer because the old one has to be drained and removed, and the pipework adapted. We give you the timing with the quote.

Do unvented cylinders need a certificate?

Yes. An unvented cylinder must be fitted by a qualified installer and notified under the building regulations. Keep the paperwork, because buyers, landlords and insurers may ask for it.

Is a dripping pipe under my cylinder dangerous?

On an unvented cylinder, water from the safety discharge pipe means a valve is opening to release pressure or heat. Switch off the water heating and call an engineer. Don't block the pipe.

Do you work in mansion blocks with communal hot water?

Yes, but in blocks with a communal system, some parts belong to the building, not the flat. We check with the managing agent before working on shared pipework.

Got something that needs fixing?

Get a free quote today — agreed before any work starts.

Free quoteCall